جزئیات محصول:
|
گواهی: | CE | وضعیت: | جدید |
---|---|---|---|
طول موج کار:: | 10.6um | قدرت: | 60W / 80W 150W |
کلید واژه ها: | پنجره های محافظ لیزری | توانایی: | سطح بالا |
قطر: | 60 میلی متر | کلمه کلیدی: | لوله لیزر |
نوع لیزر: | دستگاه برش لیزر Co2 | طول: | 160 میلی متر |
برجسته: | دستگاه برش لیزری |
لوله برش لیزری 60w / 80w / 100w / 130w / 150w / 180w Co2 برای برش لیزر Co2
مشخصات:
مدل | دارای امتیاز (W) | حداکثر توان (w) | طول (میلی متر) | قطر (میلی متر) | کاتالیز |
JSD-50-700 | 40 | 50 | 700 | 50 | آره |
JSD-50-800 | 50 | 60 | 800 | 50 | آره |
JSD-50-1000 | 50 | 70 | 1000 | 50 | آره |
JSD-55-1000 | 50 | 70 | 1000 | 55 | آره |
JSD-55-1200 | 60 | 80 | 1200 | 55 | آره |
JSD-55-1250 | 60 | 80 | 1250 | 55 | آره |
JSD-60-1200 | 60 | 80 | 1200 | 60 | آره |
JSD-60-1250 | 60 | 80 | 1250 | 60 | آره |
JSD-80-1250 | 80 | 100 | 1250 | 80 | آره |
JSD-60-1600 | 80 | 110 | 1600 | 60 | آره |
JSD-80-1200 | 90 | 100 | 1200 | 80 | آره |
JSD-80-1400 | 100 | 120 | 1400 | 80 | آره |
JSD-80-1450 | 100 | 120 | 1450 | 80 | آره |
JSD-80-1600 | 130 | 150 | 1600 | 80 | آره |
JSD-80-1650 | 130 | 160 | 1650 | 80 | آره |
JSD-80-1800 | 150 | 180 | 1800 | 80 | آره |
JSD-80-2000 | 180 | 190 | 2000 | 80 | آره |
1, first line the electrode, (+, -) is not wrong. 1 ، اول الکترود را خط کنید ، (+ ، -) اشتباه نیست. CO2 laser (laser tube) installation instructions: دستورالعمل نصب لیزر CO2 (لوله لیزر):
2, installation of cooling water pipe, the installation method of water from the negative electrode, the positive water and meet the principle of falling out, and the interface can not leak. 2 ، نصب لوله آب خنک کننده ، روش نصب آب از الکترود منفی ، آب مثبت و مطابق با اصل ریزش ، و رابط نمی تواند نشت کند. Sufficient water must be stored in the pre - storage water storage device. آب کافی باید در دستگاه ذخیره آب قبل از ذخیره سازی ذخیره شود. After water, the water cooling pipe must be used without air bubbles (must be viewed before each use). پس از آب ، لوله خنک کننده آب باید بدون حباب هوا استفاده شود (قبل از هر بار استفاده باید مشاهده شود). If the laser tube is vertically installed, please notice that there is no bubble at the top of the laser tube. اگر لوله لیزر به صورت عمودی نصب شده است ، توجه داشته باشید که هیچ حبابی در بالای لوله لیزر وجود ندارد. When the bubble exists, it will cause damage to the laser tube if it runs. هنگامی که حباب وجود داشته باشد ، در صورت کار باعث آسیب به لوله لیزر می شود.
3, in order to maintain the good performance of the laser tube, please use a temperature controlled water cooler between 20-25 degrees Celsius. 3 ، به منظور حفظ عملکرد خوب لوله لیزر ، لطفاً از کولر آبی کنترل شده دما بین 20-25 درجه سانتیگراد استفاده کنید. If the cooling water is unstable, the output power of the laser tube will be unstable. اگر آب خنک کننده ناپایدار باشد ، قدرت خروجی لوله لیزر ناپایدار خواهد بود.
4, when the laser tube is installed, there is enough space between the high pressure end of the laser tube and any other metal surface. 4 ، در هنگام نصب لوله لیزر ، فاصله کافی بین انتهای فشار بالای لوله لیزر و هر سطح فلزی دیگر وجود دارد. If the gap is too small, triggering the high pressure of the laser tube will cause fire to the metal surface, which will cause damage to the laser tube and even cause damage to other main components of the laser. اگر این شکاف خیلی کم باشد ، تحریک فشار زیاد لوله لیزر باعث آتش سوزی به سطح فلز می شود و این باعث آسیب دیدن لوله لیزر و حتی آسیب رساندن به سایر اجزای اصلی لیزر می شود.
5, it is suggested that an automatic inspection device be added to the cooling water circulation system of the laser tube, so as to prevent the laser tube from overheating due to the water failure. 5 ، پیشنهاد می شود که یک دستگاه بازرسی اتوماتیک به سیستم گردش آب خنک کننده لوله لیزر اضافه شود ، به منظور جلوگیری از گرم شدن لوله لیزر به دلیل نارسایی آب. For details, consult the supplier of the laser machine. برای جزئیات بیشتر با تهیه کننده دستگاه لیزر مشورت کنید.
تماس با شخص: Coco
تلفن: +86 13377773809